Changing a heating factor in a Samsung dryer can prevent the price of shopping for a brand new dryer or hiring an equipment restore technician. To exchange the heating factor, you will first want to collect the required instruments and supplies, together with a brand new heating factor, screwdriver, and pliers. Upon getting the required objects, observe these steps to exchange the heating factor in your Samsung dryer.
First, unplug the dryer from the facility outlet and take away the again panel of the dryer. Subsequent, find the heating factor and disconnect the wires which might be connected to it. Then, take away the outdated heating factor from the dryer. To put in the brand new heating factor, merely insert it into the dryer and reconnect the wires. Lastly, exchange the again panel of the dryer and plug it again into the facility outlet. Your Samsung dryer ought to now be working correctly.
If you’re not assured in your means to exchange the heating factor your self, it’s best to contact a certified equipment restore technician. A professional technician will be capable of rapidly and safely exchange the heating factor in your Samsung dryer and get it working correctly once more.
Security Precautions
Earlier than embarking on the duty of changing the heating factor in your Samsung dryer, it’s crucial to prioritize your security. Electrical energy and heating components can pose important dangers if correct precautions will not be taken. To make sure a secure and profitable restore, meticulously adhere to the next security measures:
1. Disconnect the Energy Supply
The primary and most important step is to disconnect {the electrical} provide to your dryer. That is a necessary security measure to stop any unintended electrical shocks or fires. Find the primary electrical panel in your house and swap off the circuit breaker or take away the fuse similar to the dryer. Confirm that the facility has certainly been disconnected by testing the dryer outlet with a voltage tester. Wait a couple of minutes to permit any residual electrical energy within the system to dissipate.
| Suggestions for Disconnecting the Energy Supply |
|---|
| – Establish the right circuit breaker or fuse for the dryer. |
| – Swap off the corresponding circuit breaker or take away the fuse. |
| – Use a voltage tester to substantiate that the outlet is now not receiving energy. |
| – Enable adequate time for the residual electrical energy to dissipate. |
Collect Vital Instruments and Supplies
Earlier than embarking on the restore, it is essential to collect the important instruments and supplies. Here is an in depth rundown of what you will want:
Supplies:
- New heating factor
- Electrical tape
- Warmth-resistant gloves (non-obligatory)
Instruments:
| Software | Function |
|---|---|
| Phillips-head screwdriver | Take away the screws securing the entry panels and heating factor |
| Torx screwdriver | Unscrew the bolts holding the heating factor in place (some fashions) |
| Multimeter | Check the continuity of the heating factor (non-obligatory) |
| Pliers (non-obligatory) | Tighten or loosen nuts or bolts |
| Protecting goggles (non-obligatory) | Shield eyes from free particles |
Extra Supplies:
Whereas not strictly mandatory, sure supplies could make the restore course of smoother:
- Flashlight: Illuminate the work space, particularly in dimly lit areas
- Store towels or rags: Clear up any particles or spills
- Digital camera: Doc the disassembly course of for simpler reassembly
- Warmth gun (non-obligatory): Soften outdated adhesive or velocity up evaporation of moisture
- Soldering iron (non-obligatory): Restore broken wires or safe new connections
Find and Take away the Rear Panel
Unplug the dryer and transfer it away from the wall.
For security functions, unplug your dryer from the facility outlet earlier than beginning any repairs. It could even be greatest to tug the dryer away from the wall to offer your self ample area to work.
Find the screws holding the rear panel in place.
Figuring out the screws that maintain the rear panel of the dryer is essential. These screws are usually situated across the perimeter of the panel, and their place could range barely relying on the dryer mannequin. Upon getting recognized the screws, proceed to the subsequent step.
Take away the screws and punctiliously carry off the rear panel.
Upon getting situated the screws, use a screwdriver to take away them. Watch out to not strip the screws or injury the rear panel when eradicating them. After eradicating all of the screws, rigorously carry the rear panel off the dryer. Word that the rear panel could also be barely heavy, so you’ll want to assist it with one hand whereas eradicating the screws with the opposite.
Disconnect Current Heating Ingredient
**Step 1: Unplug the Dryer**
Earlier than engaged on the dryer, disconnect it from the facility provide by unplugging it from the wall outlet.
**Step 2: Take away the Again Panel**
Find the screws on the again panel of the dryer and take away them utilizing a screwdriver. Rigorously carry and take away the again panel to show the internal elements.
**Step 3: Disconnect Wires**
Establish the 2 wires related to the heating factor terminals. Gently pull the wire connectors off the terminals. Make observe of which wire goes to which terminal for future reference.
**Step 4: Take away the Heating Ingredient**
The heating factor is held in place by two screws or bolts. Use a wrench or socket to loosen and take away these fasteners. Rigorously slide the heating factor out of its housing. Be aware of sharp edges and keep away from touching the factor together with your naked fingers.
| Screw/Bolt Location | Removing Technique |
|---|---|
| Prime of the housing | Loosen with a wrench or socket |
| Backside of the housing | Take away with a wrench or socket |
**Step 5: Examine the Heating Ingredient**
Visually examine the heating factor for any injury or corrosion. If the factor is broken, it’s going to should be changed earlier than reassembling the dryer.
Take away Previous Heating Ingredient
5. Disconnect the heating factor from the facility provide.
| Kind of Dryer | Steps |
|---|---|
| Gasoline Dryer |
Shut off the fuel provide to the dryer earlier than continuing. |
| Electrical Dryer |
Unplug the dryer from the facility outlet and switch off the circuit breaker or fuse for the dryer circuit |
6. Take away the screws that maintain the heating factor in place.
7. Unclip the wire terminals from the heating factor.
8. Pull the heating factor out of the dryer.
Set up New Heating Ingredient
Security Precautions
Earlier than starting any work, unplug your dryer and disconnect the facility supply. Be sure that the machine is cool to the contact.
Eradicating the Previous Heating Ingredient
- Take away the entrance panel of the dryer by unscrewing the screws on the high and pulling it ahead.
- Find the entry panel on the entrance of the dryer’s drum. Take away the screws and pull it open.
- Pull the outdated heating factor unit in the direction of you to disconnect the wires.
- Unplug the wires from {the electrical} terminals and take away the outdated heating factor.
Putting in the New Heating Ingredient
- Insert the brand new heating factor unit into the opening within the drum.
- Join the wires to {the electrical} terminals. Be sure that the connections are safe.
- Push the heating factor unit again into place and safe it with the screws.
- Reattach the entry panel and the entrance panel of the dryer.
- Plug the dryer again into the facility outlet and switch it on to check the brand new heating factor.
Suggestions for Troubleshooting
| Downside | Resolution |
|---|---|
| Dryer not heating | Examine the facility provide. Examine the wires and connections to the heating factor. Check the heating factor with a multimeter. |
| Dryer overheating | Unplug the dryer and let it calm down. Clear the lint filter and exhaust vent. Examine the thermostat and temperature sensor. |
Reconnect Electrical Wires
Now it is time to reconnect {the electrical} wires to the heating factor. Remember to match the wires to the right terminals on the factor. Usually, the crimson wire will connect with the left terminal and the white wire will connect with the proper terminal. Nevertheless, confer with your dryer’s particular wiring diagram to substantiate.
Tighten the screws on the terminals securely utilizing a screwdriver. Be sure that the wires are making good contact with the terminals to stop any free connections that might trigger arcing or different electrical points.
As soon as the wires are related, tuck them again into the insulation across the heating factor. This may assist to guard the wires from warmth injury and maintain the within of the dryer tidy.
Wiring Diagram
For fast reference, here’s a desk with a basic wiring diagram for many Samsung dryers:
| Wire Shade | Terminal |
|---|---|
| Purple | Left Terminal |
| White | Proper Terminal |
Once more, double-check your dryer’s particular wiring diagram to make sure accuracy earlier than making any connections.
Change Rear Panel
Now that the screws are eliminated, carry the rear panel up from the underside and pull it in the direction of you to detach it from the dryer. Watch out to not injury any wires or elements as you do that.
As soon as the rear panel is eliminated, you should have entry to the heating factor. The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws.
Step 8: Take away the Heating Ingredient’s Wiring
Earlier than eradicating the heating factor, it is advisable to disconnect its wiring. The heating factor has two wires related to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals.
As soon as the wires are disconnected, you may take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor could be pulled out of the dryer.
| Step 6: Find the Heating Ingredient | The heating factor is situated on the backside of the dryer, behind the drum. It’s held in place by two screws. |
| Step 7: Disconnect the Heating Ingredient’s Wiring | Earlier than eradicating the heating factor, it is advisable to disconnect its wiring. The heating factor has two wires related to it: a black wire and a white wire. Use a pair of pliers to softly pull the wires off of the heating factor’s terminals. |
| Step 8: Take away the Heating Ingredient | As soon as the wires are disconnected, you may take away the heating factor. Use a screwdriver to take away the 2 screws that maintain the heating factor in place. As soon as the screws are eliminated, the heating factor could be pulled out of the dryer. |
As soon as the outdated heating factor is eliminated, you may exchange it with the brand new one. Insert the brand new heating factor into the dryer and safe it with the 2 screws. Remember to join the wires to the heating factor’s terminals within the right order: black wire to black terminal, white wire to white terminal.
As soon as the brand new heating factor is put in, you may reattach the rear panel to the dryer. Safe the rear panel with the screws that you just eliminated earlier.
Check the Dryer
Upon getting changed the heating factor, it is very important take a look at the dryer to ensure it’s working correctly. Listed here are the steps on the right way to take a look at the dryer:
| Step | Motion |
|---|---|
| 1 | Be certain that the dryer is plugged into an outlet and that the facility swap is turned on. |
| 2 | Open the dryer door and place a moist towel inside. |
| 3 | Shut the dryer door and choose the “Regular” or “Timed Dry” cycle. |
| 4 | Press the “Begin” button to begin the dryer. |
| 5 | Let the dryer run for a couple of minutes to see if the towel will get heat. |
| 6 | If the towel will get heat, then the heating factor is working correctly. |
| 7 | If the towel doesn’t get heat, then there could also be an issue with the heating factor or different elements of the dryer. |
If you’re having issues together with your dryer, it’s best to contact a certified equipment restore technician for help.
Security Precautions Earlier than Beginning:
1. Unplug the dryer from the facility outlet and permit it to chill fully.
2. Put on gloves to guard your fingers from sharp edges.
3. Collect all mandatory instruments and components earlier than beginning.
Checking the Heating Ingredient:
1. Take away the again panel of the dryer by unscrewing the screws across the perimeter.
2. Find the heating factor, which is usually an oblong steel field with two wires related to it.
3. Unplug the wires from the heating factor utilizing needle-nose pliers.
Eradicating the Heating Ingredient:
1. Unscrew the nuts holding the heating factor in place.
2. Rigorously carry the heating factor out of the dryer cupboard.
Putting in the New Heating Ingredient:
1. Place the brand new heating factor into the dryer cupboard.
2. Tighten the nuts holding the heating factor in place.
3. Join the wires to the heating factor.
Troubleshooting Suggestions
1. If the dryer nonetheless doesn’t warmth, test the thermal fuse.
2. If the thermal fuse is blown, exchange it.
3. If the heating factor is just not getting energy, test the wiring.
4. If the wiring is broken, restore or exchange it.
5. If the dryer continues to be not heating, contact a certified equipment restore technician.
Extra Troubleshooting Suggestions:
| Attainable Trigger | Resolution |
|---|---|
| Free belt | Regulate or exchange the belt |
| Vent blockage | Clear the dryer vent |
| Defective thermostat | Change the thermostat |
| Defective relay | Change the relay |
| Defective management board | Change the management board |
7. If the dryer is making a loud noise, test the drum bearings.
8. If the drum bearings are worn, exchange them.
9. If the dryer is shaking excessively, test the shock absorbers.
10. If the shock absorbers are worn, exchange them.
Learn how to Set up a Heating Ingredient in a Samsung Dryer
Changing the heating factor in a Samsung dryer is a comparatively easy job that may be accomplished in about an hour. Nevertheless, it is very important take security precautions and observe the directions rigorously to keep away from harm or injury to the dryer.
Supplies wanted:
- New heating factor
- Screwdriver
- Wrench
- Security glasses
- Gloves
Directions:
- Unplug the dryer from the facility outlet.
- Placed on security glasses and gloves.
- Take away the again panel of the dryer by unscrewing the screws that maintain it in place.
- Find the heating factor, which is often situated on the backside of the dryer.
- Disconnect the wires from the heating factor.
- Unscrew the bolts that maintain the heating factor in place.
- Elevate the heating factor out of the dryer.
- Place the brand new heating factor into the dryer.
- Screw within the bolts to safe the heating factor in place.
- Join the wires to the heating factor.
- Change the again panel of the dryer.
- Plug the dryer again into the facility outlet.
